Armature Slot Electrostatic Fluidize Coating System Resin Insulation Machine WIND-JF
This powder coating machine composed of pre-heating zone, cooling zone, coating zone and curing zone,electrostatic powder/resin coating is widely used in micro rotor insulating coating, such as automotive, motorcycle, electric bicycle, toy and small electromotor of home appliances.
Application:
| Micro rotor insulating coating |
automotive, motorcycle, electric bicycle, toy and small electromotor |
| Vehicle components |
ABS, HVAC,window lift, seat adjuster,sunroof and antenna, windshield wiper and fuel pump armatures |
| Moving Vehicle |
motorcycle, electric bicycle |
| Home appliances |
power tool, electric toothbrush |
| Armature size OD |
8mm to 60mm |
| Armature output per shift |
2500pcs per 8 hours for armature OD size 30mm~40mm |
| Resin insulation class |
B, F, H 120℃, 155℃,180℃, For China local >155℃ is widely used |
Work process:
High frequency deoil---fan cooling---coating---outside powder clearning---curing---air cooling
Electrostatic resin coating machine composed of pre-heating zone, cooling zone, resin coating zone and
curing zone.
Rotor/Armature is transferred to electrostatic fluidizing bed by screw for coating. Isolation power is evenly
coated on its surface, and then cured by high frequency heating.
Electrostatic powder coating is generally divided into three process, they are resin coating,
remove excess powder by scratching device of motor armature or stator surface, Curing.
The powder coating process be done on the electrostatic fluid bed,then the scratching deive
clean powder, after scraping, the armature/rotor or stators pass high-frequency induction heater
to curing, in this way, the powder can be applied to an object, bonding to the substrate and coalescing
into a smooth, continuous, essentially uniform, thick coating.
Use for resin 3M or AkzoNobel include moisture-proofing and insulating armatures, rotors, stators,
buss bars and other motor parts.
The electrostatic powder coating machine contains a powder recovery recyling device,
The device comprise a dust suction pipe disposed corresponding to the coating device,
The powder cleaning device and the device located in the electrostatic powder coating machine frame.
The separate dust suction pipes are concentrated to the total dusting collecting pipe.
The total dusting piple send powder to cyclone separator,
Upper of the cyclone separator is an outlet pipe, and lower end is a powder collecting piple which
connected to powder feeder.
Parameter:
Armature OD: by customer drawing
Core length: by customer drawing
Shaft length: by customer drawing
Output: by customer request
Coating thickness: 0.15-0.5mm adjustable
Armature transfer speed: 0.1-15.meters per minute
| Model (WIND-JF) |
100 |
80GG |
80GD |
50H |
Lab model |
note |
| Part size |
Max OD |
160 |
120 |
120 |
100 |
200 |
Is able to be tailored produced |
| Max core length |
50 |
50 |
50 |
50 |
80 |
| Max shaft length |
180 |
180 |
180 |
180 |
180 |
| transfer speed m/min |
0.1-1.5 |
0.1-1.5 |
0.1-1.5 |
0.1-1.5 |
Electronic driving |
Stepless adjustable |
| output(pc/h) |
2500 |
1500 |
1500 |
800 |
10-60 |
фMax≤20mm |
| Curing method |
High frequency |
High frequency |
High frequency |
Curing oven |
Curing
oven |
Oven is prepared by customer |
| Coating thickness(mm) |
Adjustable within 0.15mm - 0.5mm |
Above parameter is only for reference
|
|
Armature Slot Electrostatic Fluidize Coating System Resin Insulation Images
|
